It’s obvious that braid should be heated very quickly and if it is too small, you won’t be able to transfer enough heat to the braid. It is also very important to choose the size and form of the soldering tip close to the width of the braid. Always match soldering iron tip to braid width.Moreover, it can interfere with other components of the circuit board and probably even damage them. If the braid is wider that a surface with unwanted solder, it will take much more time to heat the copper. It’s easy to explain: smaller widths might not remove enough solder, as the braid doesn’t absorb enough solder. It’s really of great importance to have a desoldering braid that closely matches the size of the contact. Make sure you match braid width to solder joint or contact pad.In case you are going to use a soldering wick without a flux, it would be better if you add it. Flux gives a fastest action and helps the surfaces to be heated and solder to flow. As solder wick can be bought with or without flux, make sure to match flux type to your cleaning process.
Tips and tricksīelow are some tips and tricks that will help you to improve your skills when you need to do some desoldering work or remove some excess solder from the circuit board. Note: When the desoldering braid becomes fully saturated with the removed solder, but you still need to continue working, simply cut the end of the copper braid and go on doing the same with a new portion of the solder wick. Otherwise the braid might stay at the board. Once solder is totally removed, lift up both: a soldering iron and braid at the same time.At that moment the solder will start melting and being pulled up into the desoldering braid or being absorbed by it. Place the end of the braid on the solder joint you need to desolder or on excess solder you need to remove and lightly press it.Unwind several inches of the copper braid.For instance, if I need to remove through-hole components from the circuit board, I prefer to use a solder wick or desoldering braid. Soldering wick could be used, mostly, for small repairs, removal of the excess solder in the tight joints. When to use soldering wick/desoldering braid? Having said that, risks reduction of damaging the board by the heat is also a bonus. The obvious advantage of using solder wick is a quicker wicking, which means significant reduction of solder removal/repair time. What are the advantages of using solder wick? In other words, the copper braids heat up and help the solder to get or to “wick” into it. Solder wick helps to transfer the heat through the copper braid to the solder joint.
Solder wick comes in different length, widths, and flux types. However, the most popular and easy is a solder-wick – an old and reliable brand designed more than 40 years ago, and it meets industrial and outer space specifications.Ī solder wick, or in other words a desoldering braid, is a braided piece of copper wire.
There are several ways to clean unwanted solder from the soldering board: desoldering pump, heat gun, compressed air, and more. Then go into the folder and drag and drop updflash.bin into the nand loading bar, Then write Nand.If you like soldering, you might be interested in these soldering kits What are the ways to remove excess solder?
Soldering nand x without solder serial#
Then click Show working folder and drag and drop The file that is named as the consoles serial number, to the desktop. Once CPU key is correct make sure glitch2 is selected and click Create Xebuild and it'll ask if you want to delete the SMC. It should say the CPU key is correct.ħth. Then get the CPU key and type it in on the CPU key box. Use file: Ace Time files>trinity>300MHZ>62.6>.07 and make sure XSFC is selected and click program, (Green light should Show up on the chip for a few seconds)Ħth, Unplug everything, then Turn it on and it should boot Xell. After both are done it should say "Nands Are the same" if it says "Oh no" nands are not the same and you need to do it again until you get 2 of the same Nand reads.Ĥth make sure glitch2 is selected at the top right, then Create Ecc & Write Ecc.ĥth, unplug nand x wires, then program the Ace v3 chip. connect nand x, and On jrunner Click Read Nand, get at least 2 Nand reads.
Soldering nand x without solder install#
Trinity and Corona Diagrams are below:Ģnd, install the Nand reading wires make sure nothing is bridgedģrd, plug the power into the console but don't turn it on. Nand X with Programming Cord and USB cord.Īnd all the other needed bullshit to solder.ġst.